S-LINE
For a flawless finish.
When you need a flawless finish, then the Rebel One unitized S-line is the perfect choice. This line is the ultimate classic in our range of three-dimensional abrasive materials, especially because of its multifaceted usability.
Multifaceted usability
The fact that this line can be used for so many applications is a direct result of its universal quality. But the emphasis is always initially on a flawless finish. It’s no surprise that the S-line is perfect for removing scratches or correcting abrasive flaws.
You can’t go wrong using these abrasive discs for pre-polishing either; this way, you’re sure to have a perfectly smooth and glossy surface. You can even remove a fine weld using the S-line.
Suited for:
RVS
Advantages
Allow you to finish materials in a simple and consistent way.
Perfect, consistent and reproducible finish of the workpiece.
Does not affect the geometry of the workpiece: no grinding errors.
Cooler sanding than traditional abrasives: less chance of discolouration.
Very forgiving: a mistake isn’t punished immediately.
Also suitable for materials that generate extreme heat such as titanium and cobalt alloys.
Stainless steel safe (iron free).
VOC free.
Voordelen
Laat toe om materialen op een
eenvoudige
en
consistente
manier af te werken.
Perfecte, consistente en reproduceerbare
afwerking
van het werkstuk.
Heeft geen invloed op de
geometrie
van het werkstuk: geen slijpfouten.
Koeler schuren dan traditionele schuurmiddelen: minder kans op
verkleuring
.
Zeer vergevingsgezind
: een fout wordt niet meteen afgestraft.
Ook geschikt voor materialen die extreme hitte genereren zoals
titanium
en
kobaltlegeringen
.
Veilig voor roestvrij staal (ijzervrij).
VOC-vrij.
VOC-free
Volatile Organic Compounds (VOC) stands for a group of substances including fuel and solvents. Upon vaporisation these substances cause global warming, acidification and are harmful to health. Solvent is commonly used in the production of unitised.
The entire Rebel One range, on the other hand, is 100% solvent-free, VOC free compliant and contains no polymers coming from bisphenol A.
Iron free
Iron free – stainless steel safe: no contamination.
S-line: Wide range of application uses, most universal quality.
Grain
| Silicon Carbide |
Diversity
| 5 → 7
|
Finish
|  |
Stock Removal |  |
Control over workpiece |  |
Voordelen
Laat toe om materialen op een
eenvoudige
en
consistente
manier af te werken.
Perfecte, consistente en reproduceerbare
afwerking
van het werkstuk.
Heeft geen invloed op de
geometrie
van het werkstuk: geen slijpfouten.
Koeler schuren dan traditionele schuurmiddelen: minder kans op
verkleuring
.
Zeer vergevingsgezind
: een fout wordt niet meteen afgestraft.
Ook geschikt voor materialen die extreme hitte genereren zoals
titanium
en
kobaltlegeringen
.
Veilig voor roestvrij staal (ijzervrij).
VOC-vrij.
Applications
Removing scratches on tube
Pre-polishing
Grinding with RA value
Tips & Tricks
Speed
Follow the recommended speed on the product label.
- Low speed = maximum efficiency and a better finish.
- High speed = excessive heat generation & premature wear.
Angle
Change angle in function of your application.
- Flat use = better finish.
- Used on side = increased aggressive action.
Pressure
Always apply medium pressure.
- Pressure too high = excessive heat generation & premature wear.
- Pressure too low = little or no result.
"Zigzag" movement
Use the up and down motion (zig zag) to remove the weld discoloration.
Maximum efficiency
For optimum efficiency, the pores of the finishing wheels must be opened regularly.
This can be done effortlessly with our sanding file SV19030 in combination with the sanding sheet 706GR/24/V006.
